THIN LIGHT PANELS

FRAMELIGHTS - FRAMELIGHT AND FRAMELED - THIN LIGHT PANELS WITH A PHOTO IMAGE Framelight (Framelight) is the most common type of thin light panels. At present, these panels are a staple in the thin light panel market due to their ergonomics and good exterior. Framelight light panels are thinner than ordinary lightboxes, which significantly expands their scope, improves their appearance and increases the usability of illuminated advertising. The edge lighting system allows the light panels to glow brightly and evenly, while at the same time using up to 10 times less electricity than other light boxes of the same size. The design of the light panels makes it possible to easily and quickly change the image printed on the light-enhancing film. Light weight greatly simplifies installation and maintenance. TYPES OF FRAMELITES suspended wall-mounted unilateral bilateral Framelights are for indoor use only. The framelight light panel is easily attached to the wall using dowels and screws or suspended from the ceiling using cables or chains. We can make a framelight of any size! HOW THE IMAGE CHANGES IN A FRAMELITE To replace an image in the Framelight panel: snap off the side profiles remove protective glass replace the image with a new one, if necessary, fix it in the desired position using transparent tape reinstall protective glass close profile covers WHAT IS A FRAMELITE COMPOSED OF The FrameLight system consists of a base profile to which a closing profile is fixed with stainless steel fixing springs. A special acrylic panel is illuminated by a super-bright LED strip. The easy-to-change image is printed on backlite film (1440dpi photo quality) and protected by a clear acrylic sheet. We use only high-quality profile for framelights. Depth of one-sided panel 22 mm, double-sided - 30 mm; frame width - 25-30 mm; Recommended for sizes no larger than AA. All models are backlit with LEDs. OUTDOOR THIN LIGHT PANELS An elegant replacement for bulky light boxes. Thickness from 2 cm. They are used on the street in the form of ordinary signs, but they have a winning appearance and low power consumption. SLIM-BOX - street thin light boxes (flat lightboxes) are produced using the technology of edge-lit systems with high-brightness LEDs, which makes it possible to achieve a uniformly bright result over the entire advertising surface with a minimum thickness of the light panel. The ends are finished with an aesthetic anodized aluminum profile. The flat, original design of these light boxes compares favorably with bulky conventional light boxes that fill the eyes. These panels look especially good above the entrance to small shops or salons. FEATURES OF THE THIN LIGHT PANEL The thickness of the panel is 20 - 30 mm (depending on the size of the panels). Distance from the wall 20 mm (with built-in power supplies) and close to the wall (with remote power supply) The price of the panel includes a permanent image (it is possible to replace it periodically). All elements of this product are designed for outdoor use without restrictions and have an IP54 waterproof rating. All models are equipped with an external sealed power supply. Panels are made in any size and proportion, but the maximum size cannot exceed 800 x 1200 mm. IMPORTANT INFORMATION The image in this panel model is permanent. Replacement is only possible under production conditions. The design of the panel does not provide for a quick image change. ADVANTAGES OF THE THIN PANEL FOR THE STREET An important reason for purchasing this thin light box is that it is less vulnerable to falling ice and snow in the winter, as its small thickness is too small for ice and other objects flying from above to get into it. Small power consumption. Presentable appearance. OPEN BOX - LIGHTBOX WITH DOOR A box with an opening door - OPENBOX - is designed to accommodate information, menus, announcements. OPENBOX is used when frequent and fast image replacement is required. Can be used outdoors and indoors. The door is fixed with a hexagon bolt. The hexagon wrench comes with the box. The stand is installed on top or on the sides of the box, depending on the size of the OPENBOX. There are three options for attaching an image: Series A - on adhesive tape - the simplest design, the image is glued to a transparent adhesive tape, if necessary, replacement is possible along with the image. Series B - Plexiglas flat pocket. The image is installed in a pocket, if replacement is necessary, the old image is simply removed and a new one is installed Series C - Click system. Inside the box, a click profile with plexiglass (polystyrene) is installed. The image is replaced by snapping the click profile, removing the protective screen (plexiglass or polystyrene). Then the image changes and all actions you